{"id":1062,"date":"2023-02-21T15:03:12","date_gmt":"2023-02-21T15:03:12","guid":{"rendered":"https:\/\/www.fastseal.eu\/blog\/?p=1062"},"modified":"2023-02-23T12:28:24","modified_gmt":"2023-02-23T12:28:24","slug":"machine-settings-barfeeder","status":"publish","type":"post","link":"https:\/\/fastseal.eu\/blog\/machine-settings-barfeeder\/","title":{"rendered":"Machine settings – Bar feeder"},"content":{"rendered":"\n

The bar feeder, also known as a bar loader is a separated accessory, placed behind the lathe chuck, for serial production with the objective of supplying a near continuous operation to the lathe. This is done by opening the chuck and push the raw material then closing the chuck again. The options be below allow this type of control.<\/p>\n\n\n

\n
\"\"
Lathe with bar feeder. Copyright of Gongtie company<\/figcaption><\/figure>\n<\/div>\n\n\n

The available settings are the following, and should be used together with the available templates so that a suitable configuration is made as variables and conditions must be set that enable or not the use of the bar feeder.<\/p>\n\n\n

\n
\"\"<\/figure>\n<\/div>\n\n\n

This setting and the other templates settings, on a Haas ST35 with a bar feeder, making 10 guide rings with 50×60 and 10mm height produces the following code. One push is made by the bar feeder as the total length requires more than 100mm but less than 200mm.<\/p>\n\n\n\n

%\r\nO0801 (GR01-MPS 50.000\/60.000\/10.000)\r\n(PROFILE: GR01-MPS)\r\n(MEASURES: 50.000\/60.000\/10.000)\r\n(MATERIAL: POM 46.000\/62.000 - TUBE 46.000\/62.000)\r\n(DATE OF FILE: 23\/02\/2023 @ 12:24:44)\r\n(FAST SEAL CREATOR VERSION: 5.3.1.1 BUILD 20230222)\r\n\r\n\r\n(******* BAR FEEDER *******)\r\n(PART COUNTER)\r\n#110 = 0\r\n(NUMBER OF PARTS:10)\r\n#100 = 10\r\n(BAR FEEDER MAX LENGTH: 100)\r\n#101 = 100\r\n(BAR FEEDER ADDITIONAL LENGTH: 0)\r\n#102 = 0\r\n(REQUIRED MATERIAL PER UNIT:12.85)\r\n#103 = 12.85\r\n(TOTAL MATERIAL REQUIRED:128.5)\r\n(WILL BAR FEEDER BE USED?:)\r\n(YES - SEE RECOMMENDED SETTINGS BELOW)\r\n\r\n(NUMBER OF PARTS THAT FIT PER PUSH: 7)\r\n#105 = 7\r\n(TOTAL PUSHES: 1)\r\n(BARFEEDER PUSH LENGTH D: 89.95)\r\n\r\n\r\n(FASTSEALCREATOR - MASTOR, LDA)\r\n(HAAS ST35 BARFEEDER )\r\n(LICENSED TO UNLICENSED - EVALUATION MODE )\r\n\r\n(STANDARD: YES)\r\n\r\n(********************)\r\n( INIT STRINGS       )\r\n(********************)\r\nG99 (FEED PER REVOLUTION)\r\nG21\r\nG54\r\nG00 G40 W50.\r\nN80\r\n(PARTS TO BE MADE ON CURRENT MATERIAL)\r\nIF[ [#100-#110] GE #105 ] #120=#105\r\nIF[ [#100-#110] LT #105 ] #120=[#100-#110]\r\n\r\n(START AND WAIT FOR VACUUM BEFORE EACH SERIES)                              \r\nM31 (VACCUM ON, WITH PAUSE)\r\nG04 P3.\r\n\r\nN140\r\nM97 P100 L#120\r\nIF [#110 GE #100] M99 P150 (DONE)\r\n\r\nG10 L2 P1 W87.85\r\nG105 (USES SET MANUAL BAR FEEDER VALUES)\r\nM99 P140\r\n\r\n\r\nN150\r\nM30 (PROGRAM END)\r\n\r\n\r\n(PART PROGRAM START)\r\nN100\r\n( ******* )\r\n( FACING DOWN )\r\n( ******* )\r\nG53 X0 Z0\r\nT0303\r\nG50 S[#130+250]\r\nG96 M04 S#130\r\nM31 (VACUUM ON)\r\nG00 X66.000 Z2.000 M08\r\nG01 X66.000 Z0.690 F1.000\r\n( FINISH )\r\nG01 X66.000 Z0.000 F0.140\r\nS380\r\nG01 X42.000 Z0.000 F0.120\r\nG00 X42.000 Z0.690 M09\r\n\r\n( ******* )\r\n( INSIDE )\r\n( ******* )\r\nG53 X0 Z0\r\nT0820\r\nG50 S[#130+250]\r\nG96 M04 S#130\r\nM31 (VACUUM ON)\r\nG00 X48.337 Z2.500 M08\r\nG01 X48.337 Z1.641 F1.000\r\nG01 X48.337 Z1.441 F0.140\r\nG01 X46.000 Z0.283\r\nG00 X44.800 Z0.483\r\nG00 X44.800 Z1.441\r\n( FINISH )\r\nG00 X54.317 Z1.441\r\nG01 X50.117 Z-0.659 F0.120\r\nG02 X50.000 Z-0.800 R0.200\r\nG01 X50.000 Z-9.400\r\nG02 X50.117 Z-9.541 R0.200\r\nG01 X51.700 Z-10.333\r\nG01 X51.700 Z-12.550\r\nG00 X45.000 Z-12.350\r\nG00 X45.000 Z5.000 M09\r\n\r\n( ******* )\r\n( OUTSIDE )\r\n( ******* )\r\nG53 X0 Z0\r\nT0808\r\nG50 S[#130+250]\r\nG96 M04 S#130\r\nM31 (VACUUM ON)\r\nG00 X61.613 Z2.500 M08\r\nG01 X61.613 Z1.641 F1.000\r\nG01 X61.613 Z1.441 F0.140\r\nG01 X62.000 Z1.258\r\nG00 X62.400 Z1.458\r\nG00 X62.400 Z1.441\r\n( FINISH )\r\nG00 X55.633 Z1.441\r\nG01 X59.833 Z-0.659 F0.120\r\nG03 X59.950 Z-0.800 R0.200\r\nG01 X59.950 Z-9.400\r\nG03 X59.833 Z-9.541 R0.200\r\nG01 X58.250 Z-10.333\r\nG01 X58.250 Z-12.550\r\nG00 X63.000 Z-12.350\r\nG00 X63.000 Z5.000 M09\r\n\r\n( ******* )\r\n( CUTTING )\r\n( ******* )\r\n( VACUUM LEFT ON )\r\nG53 X0 Z0\r\nT1034\r\nG50 S[#130+250]\r\nG96 M04 S#130\r\nG00 X63.950 Z3.000 M08\r\nG00 X63.950 Z-9.800\r\nG01 X49.000 Z-9.800 F0.080\r\nG00 X63.950 Z-9.800 M09\r\nG00 X63.950 Z15.000\r\n\r\nM31   (VACUUM ON)\r\nM37 G04 P1.\r\nT0303\r\nG54\r\nM01\r\n(********************)\r\n( ZERO POINT         )\r\n(********************)\r\nG40\r\nG10 L2 P1 W-12.85\r\nG00 G40 W50.\r\n(PART COUNTER UPDATE)\r\n#110=#110+1\r\nM99\r\n%\r\n<\/code><\/pre>\n","protected":false},"excerpt":{"rendered":"
The bar feeder, also known as a bar loader is a separated accessory, placed behind the lathe chuck, for serial production with the objective of supplying a near continuous operation to the lathe. This is done by opening the chuck and push the raw material then closing the chuck again. The options be below allow … <\/p>\n
Continue reading “Machine settings – Bar feeder”<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[55],"tags":[75,58],"class_list":["post-1062","post","type-post","status-publish","format-standard","hentry","category-settings","tag-barfeeder","tag-settings","entry"],"_links":{"self":[{"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/posts\/1062","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/comments?post=1062"}],"version-history":[{"count":4,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/posts\/1062\/revisions"}],"predecessor-version":[{"id":1092,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/posts\/1062\/revisions\/1092"}],"wp:attachment":[{"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/media?parent=1062"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/categories?post=1062"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/fastseal.eu\/blog\/wp-json\/wp\/v2\/tags?post=1062"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}